
The clamping and control levers move in the same direction. When clamping is obtained, the control lever is in the vertical position. The light version of the series presented in this catalogue has a retaining force between 75 and 875 daN, while the heavy version has a retaining force between 1000 and 3000 daN. The heavy version is used when highly intense resistant forces are used, for example when closing jigs for foams, polyurethanes, etc.
The clamp of this series are built to be easily disassembled for reworking of the individual elements depending on the requirements of use.
PERFORMANCE FOR THE LIGHT SERIES: Components in case-hardening sheet steel. Hardened and tempered supporting pivots. Supporting bushes (for sizes from 130 daN and over) hardened by cementation and ground. The clamping lever is shorn and reinforced in the points of maximum stress. In the closing movement, it is guided laterally to ensure greater stability against possible transverse stresses. Finishing of the series: galvanized
FOR THE HEAVY SERIES: The pivots and supporting bushes are made of tempered and ground steel. The other parts are made of weldable steel. Finishing of the series: phosphated.
The red handles are made of polyurethane and are resistant to oils, solvents and other chemical agents.
In order to prevent accidental openings, caused by vibrations, some tools of this series are provided with a device called, "safety device", suitable for maintaining the clamp in a closed position. This device is also able to lock the tool in open position (Pat.Pend.)

Toggle clamp Form A - Form E
Toggle clamps - Vertical series
Also available in stainless steel material
Vertical series with folded base.
Some sizes of this series are also produced in stainless steel and are shown below in red.
Material: Galvanized steel or AISI 304 stainless steel
Riveted pivots: Galvanized steel or AISI 304 stainless steel
Supporting bushes: Hardened and ground steel (for sizes ?130)
Handles: Red polyurethane resistant to oils, grease and other chemical agents.
Performance: Form A and form AX with open clamping lever and two flanged washers.
Form E and form EX with full clamping lever and bolt retainers to be welded in the desired position and angle.
Spindles: To be ordered separately (see Accessories Series)
Features and applications: During the closing, the clamping lever is guided laterally to ensure greater stability against possible transverse stresses.
A special grease is placed between two contacting surfaces during assembly.
You can find this series in pneumatic version in "Pneumatic series"

Toggle clamp Form B - Form F
Toggle clamps - Vertical series
Also available in stainless steel material
Vertical series with straight base.
Some sizes of this series are also produced in stainless steel and are shown below in red.
Material: Galvanized steel or AISI 304 stainless steel
Riveted pivots: Galvanized steel or AISI 304 stainless steel
Supporting bushes: Hardened and ground steel (for sizes ?130)
Handles: Red polyurethane resistant to oils, grease and other chemical agents.
Performance: Form B and form BX with open clamping lever and two flanged washers.
Form F and form FX with full clamping lever and bolt retainers to be welded in the desired position and angle.
Spindles: To be ordered separately (see Accessories Series)
Features and applications: During the closing, the clamping lever is guided laterally to ensure greater stability against possible transverse stresses.
A special grease is placed between two contacting surfaces during assembly.

Toggle clamp Form AL - Form EL
Toggle clamps - Vertical series
New
Also available in stainless steel material
Vertical series with folded base and with anti-realease lever. "Patent Pending"
Some sizes of this series are also made of stainless steel and are shown in red.
Material: Galvanized steel or AISI 304 stainless steel
Riveted pivots: Galvanized steel or AISI 304 stainless steel
Supporting bushes: Hardened and ground steel (for sizes >=130)
Handles: Red polyurethane, resistant to oils, grease and other chemical agents.
Performance: Form AL and form ALX with open clamping lever and two flanged washers.
Form EL and form ELX with full clamping lever and bolt retainers to be welded in the desired position and angle.
Spindles: To be ordered separately (see Accessories Series)
Features and applications: The main feature of this series is the special anti-release lever with the purpose of avoiding any accidental openings caused by vibrations; these tools are designed to prevent the operator's fingers from being crushed by the levers when opening. During the closing, the clamping lever is guided laterally to ensure greater stability against possible transverse stresses.
A special grease is placed between two contacting surfaces during assembly.
Data sheet

Toggle clamp Form BL - Form FL
Toggle clamps - Vertical series
Also available in stainless steel material
Vertical series with folded base and with anti-realease lever. "Patent Pending"
Some sizes of this series are also made of stainless steel and are shown in red.
Material: Galvanized steel or AISI 304 stainless steel
Riveted pivots: Galvanized steel or AISI 304 stainless steel
Supporting bushes: Hardened and ground steel (for sizes >=130)
Handles: Red polyurethane, resistant to oils, grease and other chemical agents.
Performance: Form BL and form BLX with open clamping lever and two flanged washers.
Form FL and form FLX with full clamping lever and bolt retainers to be welded in the desired position and angle.
Spindles: To be ordered separately (see Accessories Series)
Features and applications: The main feature of this series is the special anti-release lever with the purpose of avoiding any accidental openings caused by vibrations; these tools are designed to prevent the operator's fingers from being crushed by the levers when opening. During the closing, the clamping lever is guided laterally to ensure greater stability against possible transverse stresses.
A special grease is placed between two contacting surfaces during assembly.

Toggle clamp Form ELS-FLS
Toggle clamps - Vertical series
New
Vertical series with anti-release lever and extended clamping lever
Material:Galvanized steel
Riveted pivots:Galvanized steel
Supporting bushes: Hardened and ground steel
Handles: Red polyurethane resistant to oils, grease and other chemical agents.
Performance: Form ELS with extended clamping lever and folded base. Form FLS with extended clamping lever and straight base.
Spindles:To be ordered separately.
Extensions:The models are supplied with AP6 and AP8 extension as per the drawing and with two flanged washers.
Features and applications:The main features of this series are the special anti-release lever and the special extension of the locking arm to facilitate the specific use in control templates; these tools are designed to prevent the operator's fingers from being crushed by the levers when opening. During the closing, the clamping lever is guided laterally to ensure greater stability against possible transverse stresses.
A special grease is placed between two contacting surfaces during assembly.

Toggle clamp Form AV - Form EV
Toggle clamps - Vertical series
Vertical series with folded and front base.
Material: Galvanized steel
Riveted pivots: Galvanized steel
Supporting bushes: Hardened and ground steel
Handles: Red polyurethane resistant to oils, grease and other chemical agents.
Performance: Form AV with open clamping lever and two flanged washers.
Form EV with full clamping lever and bolt retainers to be welded in the desired position and angle.
Spindles: To be ordered separately (see Accessories Series)
Features and applications: During the closing, the clamping lever is guided laterally to ensure greater stability against possible transverse stresses.
A special grease is placed between two contacting surfaces during assembly.
You can find this series in pneumatic version in "Pneumatic series"

Toggle clamp Form AVF - Form EVF
Toggle clamps - Vertical series
Vertical series with straight and front base.
Material: Galvanized steel
Riveted pivots: Galvanized steel
Supporting bushes: Hardened and ground steel
Handles: Red polyurethane resistant to oils, grease and other chemical agents.
Performance: Form AVF with open clamping lever and two flanged washers.
Form EVF with full clamping lever and bolt retainers to be welded in the desired position and angle.
Spindles: To be ordered separately (see Accessories Series)
Features and applications: During the closing, the clamping lever is guided laterally to ensure greater stability against possible transverse stresses.
A special grease is placed between two contacting surfaces during assembly.
You can find this series in pneumatic version in "Pneumatic series"

Toggle clamp Heavy vertical series
Toggle clamps - Vertical series
Heavy vertical series.
Material: Weldable phosphated steel
Supporting bushes: Hardened and ground steel
Handles: Red polyurethane resistant to oils, grease and other chemical agents.
Features and applications: Series generally used for heavy applications requiring which require major resistant forces. The clamps of this series arebuilt to be easily disassembled for reworking of the individual elements depending on the requirements of use.